Provins Sirock Technology Site

Posts Tagged ‘IP’

For CCNA exam success, you had better know what split horizon is, how to turn it off, and when to turn it off. Knowing when to turn split horizon off is also important in production networks, because it can cause a hub-and-spoke network to have incomplete routing tables on the spokes.

Split horizon exists for a very good reason – routing loop prevention. The rule of split horizon states that a router cannot send an advertisement for a route out the same interface that it came in on. Split horizon is on by default on all interfaces running RIP, IGRP, and EIGRP.

In this CCNA tutorial, R1 will serve, as the hub and R2 and R3 will be the spokes. We’ll first configure EIGRP over the 172.16.123.0 /24 network, the network connecting the three routers.

R1#conf t

R1(config)#router eigrp 100

R1(config-router)#no auto-summary

R1(config-router)#network 172.12.123.0 0.0.0.255

R2#conf t

R2(config)#router eigrp 100

R2(config-router)#no auto-summary

R2(config-router)#network 172.12.123.0 0.0.0.255

R3#conf t

R3(config)#router eigrp 100

R3(config-router)#no auto-summary

R3(config-router)#network 172.12.123.0 0.0.0.255

Running show ip eigrp neighbor on R1 shows that adjacencies to R2 and R3 are up.

R1#show ip eigrp neighbor

IP-EIGRP neighbors for process 100

H Address Interface Hold Uptime SRTT RTO Q Seq Type

(sec) (ms) Cnt Num

1 172.12.123.3 Se0/0 11 00:02:45 1 5000 0 1

0 172.12.123.2 Se0/0 161 00:03:01 1 5000 0 1

Each router will now advertise its loopback address via EIGRP.

R1#conf t

R1(config)#router eigrp 100

R1(config-router)#network 1.1.1.0 0.0.0.255

R2#conf t

R2(config)#router eigrp 100

R2(config-router)#network 2.2.2.0 0.0.0.255

R3#conf t

R3(config)#router eigrp 100

R3(config-router)#network 3.3.3.0 0.0.0.255

Running show ip eigrp route on each router shows that R1 has a route for both R2’s and R3’s loopback. R2 and R3 will only see R1’s loopback address, and not each other’s. Why?

R1#show ip route eigrp

2.0.0.0/24 is subnetted, 1 subnets

D 2.2.2.0 [90/2297856] via 172.12.123.2, 00:03:19, Serial0/0

3.0.0.0/24 is subnetted, 1 subnets

D 3.3.3.0 [90/2297856] via 172.12.123.3, 00:03:04, Serial0/0

R2#show ip route eigrp

1.0.0.0/24 is subnetted, 1 subnets

D 1.1.1.0 [90/2297856] via 172.12.123.1, 00:03:40, Serial0/0.123

R3#show ip route eigrp

1.0.0.0/24 is subnetted, 1 subnets

D 1.1.1.0 [90/2297856] via 172.12.123.1, 00:05:17, Serial0/0.31

EIGRP uses Split Horizon by default to prevent routing loops. In this lab, though, it prevents full network reachability. R2 and R3 both form neighbor relationships with R1’s Serial physical interface. R2 advertises its loopback address to R1’s Serial interface, as does R3. Split Horizon does not allow a route to be advertised back out the same interface it was received on. This prevents R1 from advertising R2’s loopback to R3, or R3’s loopback to R2.
Read the rest of this entry »

The OSI model is the model that most networking personnel are familiar with, but to earn your CCNA, you need to know the OSI model, the TCP/IP model, and how the two map to each other.

The four layers of the TCP/IP architecture can be compared to certain levels of the OSI model. It’s important to know what each level of the TCP/IP protocol architecture does, and how these layers map to the OSI model.

The Application Layer of the TCP/IP model performs much the same tasks as the Application, Presentation, and Session layers of the OSI model.

The Transport layer in the TCP/IP architecture is similar to the Transport layer in the OSI model. This layer can use TCP or UDP as well.

The Internetwork layer in the TCP/IP architecture uses IP addresses to determine how packets should be routed. Remember that the OSI model uses IP addresses, or “Layer 3 Addresses”, at the Network layer. The two layers do much the same thing. This layer is also referred to in the TCP/IP model as the Internet layer.
Read the rest of this entry »

In studying for your CCNA exam and preparing to earn this valuable certification, you may be tempted to spend little time studying static routing and head right for the more exciting dynamic routing protocols like RIP, EIGRP, and OSPF. This is an understandable mistake, but still a mistake. Static routing is not complicated, but it’s an important topic on the CCNA exam and a valuable skill for real-world networking.

To create static routes on a Cisco router, you use the ip route command followed by the destination network, network mask, and either the next-hop IP address or the local exit interface. It’s vital to keep that last part in mind – you’re either configuring the IP address of the downstream router, or the interface on the local router that will serve as the exit interface.

Let’s say your local router has a serial0 interface with an IP address of 200.1.1.1/30, and the downstream router that will be the next hop will receive packets on its serial1 interface with an IP address of 200.1.1.2/30. The static route will be for packets destined for the 172.10.1.0 network. Either of the following ip route statements would be correct.

R1(config)#ip route 172.10.1.0 255.255.255.0 200.1.1.2 (next-hop IP address)

OR

R1(config)#ip route 172.10.1.0 255.255.255.0 serial0 ( local exit interface)

You can also write a static route that matches only one destination. This is a host route, and has 255.255.255.255 for a mask. If the above static routes should only be used to send packets to 172.10.1.1., the following commands would do the job.
Read the rest of this entry »

The Computer is a very complicated device we use for our every day comfort and the importance of some of its numerical aspects is sometimes neglected. For example: a different number is given to each computer when its user goes online or when it is part of a network. This number is the IP address and knowing about it is like knowing where you live…

What’s my IP and what do its numbers stand for?
IP stands for Internet Protocol and the address is formed from 4 numbers separated by periods. The IP address format is a 32 bit numeric one and each number can be from 0 to 255. The IP address consists of two parts: first one represent the network number and it is similar for more than one user (like the number of a street) and second represents the host name which is different for each user (like the house number). To increase the number of available IP addresses within big networks with a lot of users or small networks with few hosts, the address is divided into 4 classes (A, B, C, and D)

Having an IP address it’s like having a last name in a network. To identify a computer in a network (LAN-local area network, WAN-wide area network or on the Internet) it has to have an IP address. This number is similar to a phone number or to a zip code. It is unique and without it the device or computer can not be used in a network area. Within an isolated network the computers can be assigned different random IP addresses, but if a private network needs to be connected to the Internet the IP has to be registered so that its uniqueness is verified.
Read the rest of this entry »